$54.99
In stock, ready to ship. Documentation can be found here. Shipping v1.1.
The Duet 3 Expansion 1XD is a CAN-FD connected expansion board for the Duet 3 Mainboard that provides connection to an external stepper driver and associated peripherals. It has standard Duet 3 RJ11 connectors for daisy-chaining the CAN-FD bus and accepts up to 48V to allow sharing power supplies with stepper drivers up to 48V.
The documentation contains more details, but a summary of the feature set includes:
As of May 12th, 2021, all Duet3D products purchased from Filastruder will be eligible for a 12-month limited warranty. For more information, visit http://www.duet3d.com/warranty.
Feature | Duet 2 WiFi | Duet 2 Ethernet | Duet 2 Maestro | Duet 3 6HC | Duet 3 Mini 5+ WiFi | Duet 3 Mini 5+ Ethernet |
---|---|---|---|---|---|---|
Processor | ATSAM4E8E | ATSAM4S8C | ATSAME70Q20B | ATSAMD51P20A | ATSAME54P20A | |
Processor features | 120MHz ARM Cortex M4F, 512Kb flash, 128Kb RAM, hardware floating point (single precision), DMA, 2Kb cache | 120MHz ARM Cortex M4, 512Kb flash, 128Kb RAM, DMA | 300MHz ARM Cortex M7, 1Mb flash, 384Kb RAM, hardware floating point (double precision), DMA, 32Kb cache | 120MHz ARM Cortex M4F, 1Mb flash, 256Kb RAM, hardware floating point (single precision), DMA, 4Kb cache | ||
Networking | 2.4GHz WiFi | 10BaseT/100BaseTX Ethernet | 10BaseT/100BaseTX Ethernet | 10BaseT/100BaseTX Ethernet, or via attached SBC | 2.4GHz WiFi | 10BaseT/100BaseTX Ethernet |
Support for attached Raspberry Pi or other Single Board Computer (SBC) | No | No | Yes | Yes | ||
Stepper drivers on-board | 5 x TMC2660 | 5 x TMC2224 | 6 x TMC2160 or TMC5160 | 5 x TMC2209 | ||
Stepper driver features | Up to 2.4A peak current, microstep interpolation from x16 to x256, stall detection | Up to 1.4A peak current, microstep interpolation from any setting to x256, stealthChop2 | Up to 6.3A peak current, microstep interpolation from any setting to x256, stall detection, stealthChop2 | Up to 2.0A peak current (TBC), microstep interpolation from any setting to x256, stall detection, stealthChop2 | ||
Stepper driver expansion | Up to 7 additional stepper drivers, of which up to 5 can be TMC2660 | Up to 2 additional TMC2208 or TMC2224 stepper drivers | Almost unlimited expansion using CAN-connected expansion boards | 3 additional TMC2209 stepper drivers | ||
External stepper driver support | Up to 7 external stepper drivers when not using DueX expansion board. Signal levels are 3.3V. A 4-channel expansion breakout board is available to level shift them to 5V. | Not supported | Via CAN bus | In principle, up to 3 external stepper drivers could be connected in place of the 3-driver expansion board. Signal levels are 3.3V. | ||
Heater outputs | Bed heater (up to 18A), 2 x extruder heater (up to 6A each) | Bed heater (up to 18A TBC), 2 x extruder heater (up to 6A each) | Bed heater (up to 18A TBC), 3 x extruder heater (up to 6A each) | Bed heater (up to 18A TBC), 2 x extruder heater (up to 5A each) | ||
Thermistor/PT1000 inputs | 3, optimised for 100k thermistors, can support PT1000 sensors with reduced accuracy | 4, optimised for 100K thermistors and PT1000 sensors | 4, optimised for 100K thermistors and PT1000 sensors | 3, optimised for 100K thermistors and PT1000 sensors | ||
PT100 and thermocouple daughter board support | 2 boards (4 channels) | 2 boards (4 channels) - second board available only if I2C expansion pins are not used | 2 boards (4 channels) | 1 board (2 channels) | ||
Heater/thermistor expansion | 5 more extruder heater outputs and thermistor inputs, 2 more PT100/thermocouple daughter boards (4 channels) | None | Almost unlimited via CAN-connected expansion boards | None | ||
Endstop or filament monitor inputs | 5 on-board (STP pins are 8V-tolerant on revision 1.04 and later), 7 expansion | 5 on-board (STP pins are 30V-tolerant) | 9 on-board I/O connectors for endstop, filament monitor, Z probe or PanelDue connection. Inputs are 30V-tolerant. Almost unlimited expansion via CAN-connected expansion boards. | 6 on-board I/O connectors plus 2 input-only connectors for endstop, filament monitor, Z probe or PanelDue connection. Inputs are 30V-tolerant. | ||
Endstop status LEDs | Yes | No | No | No | ||
Z probe connector | 4-pin with IN/GND/MOD/3V3 pins (IN pin is 30V-tolerant in revision 1.04 and later) | 5-pin with IN/GND/MOD/3V3/5V pins (IN pin is 30V-tolerant) | See under Endstop or filament monitor inputs | See under Endstop or filament monitor inputs | ||
Fan outputs | 3 controlled fans, 2 always-on fan connectors, voltage selectable between VIN, 5V or external supply (all fans together); 6 more controlled fans on expansion board | 3 controlled fans, 1 always-on fan connector, voltage selectable between VIN, 5V or external supply in 2 banks | 6 controlled fans of which 3 support 4-wire fans with PWM and tacho wires, voltage selectable between VIN and 12V in 2 banks | 4 controlled fans of which 2 support 4-wire fans with PWM and tacho wires, voltage selectable between VIN and 12V in 2 banks | ||
Servo support | Up to 5 via expansion connector (3.3V drive unless expansion board used) | 1 servo output on board with 5V drive (shares the output with the Z probe MOD pin and the diagnostic LED) | See under Endstop and filament monitor inputs. Also one output with 5V signal level for servo, laser or VFD converter (shared control signal with one of the 2-wire fan outputs). | See under Endstop and filament monitor inputs. Also one output with 5V signal level for servo, laser or VFD converter (shared control signal with one of the 2-wire fan outputs). | ||
Input power voltage | 11V to 25V | 11V to 28V | 11V to 48V | 11V to 25V | ||
Power monitoring | VIN voltage and input to on-board 5V regulator | VIN voltage | VIN voltage and 12V regulator output voltage | VIN voltage | ||
LCD support | PanelDue colour touch screen | PanelDue colour touch screen, 12864 mono graphics display (5V signal levels, ST7920 controller) | Typically provided by HDMI touch screen attached to the SBC. PanelDue also supported. | PanelDue colour touch screen, mini 12864 mono graphics display (3.3V signal levels, ST7567 controller) | ||
LED strip support | No | No | Neopixel (max. 50 LEDs) or DotStar | Neopixel (max. 50 LEDs, external 5V power required; not available if Mini 12864 display uses Neopixel lighting) | ||
Other expansion | 4 GPIO pins on Duex 2/Duex 5 expansion board, 16 GPIO pins on third-party SX1509B-based I/O expansion board | 2 pins usable as analog inputs, GPIO, or UART; 2 pins usable as I2C or GPIO | Almost unlimited expansion via CAN-connected expansion boards | Via I/O ports only | Via I/O ports only. Possibility of expansion via CAN later using a daughter board. | |
SD card interface speed | 20Mbytes/sec | 15Mbytes/sec | 25Mbytes/sec | 15Mbytes/sec (may be increased) | ||
RepRapFirmware versions available | 2.0 series, 3.0 series | 2.0 series, 3.0 series | 3.0 series | 3.0 series |
Feature | Duet 0.6 | Duet 0.8.5 |
---|---|---|
Processor | ATSAM3X8E | ATSAM3X8E |
Processor features | ARM Cortex M3, 512Kb flash, 96Kb RAM, DMA | ARM Cortex M3, 512Kb flash, 96Kb RAM, DMA |
Networking | Ethernet | Ethernet |
Stepper drivers on-board | 4 x A4982 | 5 x A4982 |
Stepper driver features | Up to 2.0A peak current, x16 microstepping | Up to 2.0A peak current, x16 microstepping |
Stepper driver expansion | Up to 4 additional stepper drivers | Up to 4 additional stepper drivers |
Heater outputs | Bed heater (up to about 11A), extruder heater (up to 4A), up to 4 more extruder heaters on DueX4 expansion board | Bed heater (up to about 13A), 2 x extruder heater (up to 4A), up to 4 more extruder heaters on DueX4 expansion board (last one shared with Fan 1) |
Thermistor inputs | 2 | 3 |
Heater/thermistor expansion | 4 more extruder heater outputs and thermistor inputs on DueX4 | 4 more extruder heater outputs and thermistor inputs on DueX4 |
Endstop or filament monitor inputs | 4 on-board, 4 expansion | 5 on-board, 4 expansion |
Endstop status LEDs | Yes | Yes |
Z probe connector | No, use expansion connector | 4-pin with IN/GND/MOD/3V3 pins |
Fans | 1 controlled fan | 2 controlled fans |
Input power voltage | 11V to 30V | 11V to 28V |
Power monitoring | No | No |
LCD support | PanelDue colour touch screen (via expansion connector) | PanelDue colour touch screen (dedicated connector) |
SD card interface speed | 21Mbytes/sec | 21Mbytes/sec |
RepRapFirmware versions available | 1.x series (latest is 1.26.1) | 1.x series (latest is 1.26.1) |