Duet 2 Wifi

$169.99

Type
Antenna

In stock, ready to ship.

Internal antenna has been discontinued in favor of external antenna. Documentation can be found here.


Features:

Duet 2 Wifi features include a dedicated wifi module, higher stepper and heater current ratings, and more accurate temperature control. More features below:

  • Powerful 32 Bit Processor Atmel SAM4E8E: 120MHz ARM Cortex-M4 microcontroller
  • Super quiet TMC2660 stepper drivers SPI controlled stepper drivers capable of up to 256 microstepping. Current and microsteps can both be changed on the fly for optimum speed and power efficiency. Each stepper driver is rated for up to 2.4 amps.
  • Dual extruders 3 heater/thermistor channels for a heated bed and 2 extruders. 3 PWM controllable and 2 always-on fans. These can be run from either the input voltage, from 5V, or from external power for added flexibility.
  • Dedicated Wifi moduleRunning on a separate processor, this leaves the main processor free to do precise stepper pulse timing and implement other advanced features. Runs on the 2.4Ghz frequency.
  • Touch Screen Support - The optional PanelDue controller provides a full colour graphic touch screen controller with virtual keyboard. Also talks G-code for maximum flexibility.
  • Up to 7 extruders - Support for a further 5 stepper drivers and heaters on the expansion header. Firmware support for mixing nozzles and remapping axes to use high power external drivers.
  • Easy to configure - Setup your printer and update the firmware through the web interface. No need to compile your own firmware.

The Duet 2 Wifi uses the Duet Web Control interface for control over wifi. You can check out a simulated version by clicking here.  

What's in the box:
  •  The board itself
  •  Preloaded MicroSD card
  •  USB cable
  •  Connector kit, in case you need to crimp your own cables (crimping tool not included)
Ordering Options:
  • PT100 daughterboard - Plugs into the Duet 2 Wifi, allowing for PT100 sensor measurements. Analog PT100 amplifiers/signal boards are not compatible with the Duet Wifi. This daughterboard accepts 1 or 2 PT100 sensors.
  • Type K Thermocouple Daughterboard - Plugs into the Duet Wifi, allowing for Type K Thermocouple measurements. Analog Type K Thermocouple amplifiers/signal boards are not compatible with the Duet Wifi. This daughterboard accepts 1 or 2 Type K Thermocouple sensors.
  • External Antenna  - Uses an ESP-07S and external antenna for improved signal strength.

As of May 12th, 2021, all Duet3D products purchased from Filastruder will be eligible for a 12 month limited warranty. For more information, visit http://www.duet3d.com/warranty.

Reviews:

ARM M4F processor (faster than the M3s in Due and Smoothie v1), runs RepRapFirmware (which is very nice), uses super-fancy SPI-controlled TMC2660 drivers, and has an onboard ESP8266 for wifi. Obviously I also had to hook up a PanelDue for sweet touchscreen action. I like that the built-in web interface does most of what OctoPrint does. (No slicing, camera support is less clean, but it does all the machine control and file upload stuff.) Avoids USB streaming processor load and frees up an OctoPi to move to another printer. - Ryan Carlyle

I love the Duet WiFi. The web interface and PanelDue are both awesome in their own right but nothing you couldn't have before. With the fans off you can barely hear the steppers at all in 16X + interpolation mode. The steppers being silent and the whole thing being wrapped up in a neat package with WiFi on top make the experience so pleasant compared with anything else I've used so far. - David Martin

The Duet family of motion control electronics

Current production Duets
Feature Duet 2 WiFi Duet 2 Ethernet Duet 2 Maestro Duet 3 6HC Duet 3 Mini 5+ WiFi Duet 3 Mini 5+ Ethernet
Processor ATSAM4E8E ATSAM4S8C ATSAME70Q20B ATSAMD51P20A ATSAME54P20A
Processor features 120MHz ARM Cortex M4F, 512Kb flash, 128Kb RAM, hardware floating point (single precision), DMA, 2Kb cache 120MHz ARM Cortex M4, 512Kb flash, 128Kb RAM, DMA 300MHz ARM Cortex M7, 1Mb flash, 384Kb RAM, hardware floating point (double precision), DMA, 32Kb cache 120MHz ARM Cortex M4F, 1Mb flash, 256Kb RAM, hardware floating point (single precision), DMA, 4Kb cache
Networking 2.4GHz WiFi 10BaseT/100BaseTX Ethernet 10BaseT/100BaseTX Ethernet 10BaseT/100BaseTX Ethernet, or via attached SBC 2.4GHz WiFi 10BaseT/100BaseTX Ethernet
Support for attached Raspberry Pi or other Single Board Computer (SBC) No No Yes Yes
Stepper drivers on-board 5 x TMC2660 5 x TMC2224 6 x TMC2160 or TMC5160 5 x TMC2209
Stepper driver features Up to 2.4A peak current, microstep interpolation from x16 to x256, stall detection Up to 1.4A peak current, microstep interpolation from any setting to x256, stealthChop2 Up to 6.3A peak current, microstep interpolation from any setting to x256, stall detection, stealthChop2 Up to 2.0A peak current (TBC), microstep interpolation from any setting to x256, stall detection, stealthChop2
Stepper driver expansion Up to 7 additional stepper drivers, of which up to 5 can be TMC2660 Up to 2 additional TMC2208 or TMC2224 stepper drivers Almost unlimited expansion using CAN-connected expansion boards 2 additional TMC2209 stepper drivers
External stepper driver support Up to 7 external stepper drivers when not using DueX expansion board. Signal levels are 3.3V. A 4-channel expansion breakout board is available to level shift them to 5V. Not supported Via CAN bus In principle, up to 2 external stepper drivers could be connected in place of the 2-driver expansion board. Signal levels are 3.3V.
Heater outputs Bed heater (up to 18A), 2 x extruder heater (up to 6A each) Bed heater (up to 18A TBC), 2 x extruder heater (up to 6A each) Bed heater (up to 18A TBC), 3 x extruder heater (up to 6A each) Bed heater (up to 18A TBC), 2 x extruder heater (up to 5A each)
Thermistor/PT1000 inputs 3, optimised for 100k thermistors, can support PT1000 sensors with reduced accuracy 4, optimised for 100K thermistors and PT1000 sensors 4, optimised for 100K thermistors and PT1000 sensors 3, optimised for 100K thermistors and PT1000 sensors
PT100 and thermocouple daughter board support 2 boards (4 channels) 2 boards (4 channels) - second board available only if I2C expansion pins are not used 2 boards (4 channels) 1 board (2 channels)
Heater/thermistor expansion 5 more extruder heater outputs and thermistor inputs, 2 more PT100/thermocouple daughter boards (4 channels) None Almost unlimited via CAN-connected expansion boards None
Endstop or filament monitor inputs 5 on-board (STP pins are 8V-tolerant on revision 1.04 and later), 7 expansion 5 on-board (STP pins are 30V-tolerant) 9 on-board I/O connectors for endstop, filament monitor, Z probe or PanelDue connection. Inputs are 30V-tolerant. Almost unlimited expansion via CAN-connected expansion boards. 6 on-board I/O connectors plus 2 input-only connectors for endstop, filament monitor, Z probe or PanelDue connection. Inputs are 30V-tolerant.
Endstop status LEDs Yes No No No
Z probe connector 4-pin with IN/GND/MOD/3V3 pins (IN pin is 30V-tolerant in revision 1.04 and later) 5-pin with IN/GND/MOD/3V3/5V pins (IN pin is 30V-tolerant) See under Endstop or filament monitor inputs See under Endstop or filament monitor inputs
Fan outputs 3 controlled fans, 2 always-on fan connectors, voltage selectable between VIN, 5V or external supply (all fans together); 6 more controlled fans on expansion board 3 controlled fans, 1 always-on fan connector, voltage selectable between VIN, 5V or external supply in 2 banks 6 controlled fans of which 3 support 4-wire fans with PWM and tacho wires, voltage selectable between VIN and 12V in 2 banks 4 controlled fans of which 2 support 4-wire fans with PWM and tacho wires, voltage selectable between VIN and 12V in 2 banks
Servo support Up to 5 via expansion connector (3.3V drive unless expansion board used) 1 servo output on board with 5V drive (shares the output with the Z probe MOD pin and the diagnostic LED) See under Endstop and filament monitor inputs. Also one output with 5V signal level for servo, laser or VFD converter (shared control signal with one of the 2-wire fan outputs). See under Endstop and filament monitor inputs. Also one output with 5V signal level for servo, laser or VFD converter (shared control signal with one of the 2-wire fan outputs).
Input power voltage 11V to 25V 11V to 28V 11V to 48V 11V to 25V
Power monitoring VIN voltage and input to on-board 5V regulator VIN voltage VIN voltage and 12V regulator output voltage VIN voltage
LCD support PanelDue colour touch screen PanelDue colour touch screen, 12864 mono graphics display (5V signal levels, ST7920 controller) Typically provided by HDMI touch screen attached to the SBC. PanelDue also supported. PanelDue colour touch screen, mini 12864 mono graphics display (3.3V signal levels, ST7567 controller)
LED strip support No No Neopixel (max. 50 LEDs) or DotStar Neopixel (max. 50 LEDs, external 5V power required; not available if Mini 12864 display uses Neopixel lighting)
Other expansion 4 GPIO pins on Duex 2/Duex 5 expansion board, 16 GPIO pins on third-party SX1509B-based I/O expansion board 2 pins usable as analog inputs, GPIO, or UART; 2 pins usable as I2C or GPIO Almost unlimited expansion via CAN-connected expansion boards Via I/O ports only Via I/O ports only. Possibility of expansion via CAN later using a daughter board.
SD card interface speed 20Mbytes/sec 15Mbytes/sec 25Mbytes/sec 15Mbytes/sec (may be increased)
RepRapFirmware versions available 2.0 series, 3.0 series 2.0 series, 3.0 series 3.0 series 3.0 series
Legacy Duets
Feature Duet 0.6 Duet 0.8.5
Processor ATSAM3X8E ATSAM3X8E
Processor features ARM Cortex M3, 512Kb flash, 96Kb RAM, DMA ARM Cortex M3, 512Kb flash, 96Kb RAM, DMA
Networking Ethernet Ethernet
Stepper drivers on-board 4 x A4982 5 x A4982
Stepper driver features Up to 2.0A peak current, x16 microstepping Up to 2.0A peak current, x16 microstepping
Stepper driver expansion Up to 4 additional stepper drivers Up to 4 additional stepper drivers
Heater outputs Bed heater (up to about 11A), extruder heater (up to 4A), up to 4 more extruder heaters on DueX4 expansion board Bed heater (up to about 13A), 2 x extruder heater (up to 4A), up to 4 more extruder heaters on DueX4 expansion board (last one shared with Fan 1)
Thermistor inputs 2 3
Heater/thermistor expansion 4 more extruder heater outputs and thermistor inputs on DueX4 4 more extruder heater outputs and thermistor inputs on DueX4
Endstop or filament monitor inputs 4 on-board, 4 expansion 5 on-board, 4 expansion
Endstop status LEDs Yes Yes
Z probe connector No, use expansion connector 4-pin with IN/GND/MOD/3V3 pins
Fans 1 controlled fan 2 controlled fans
Input power voltage 11V to 30V 11V to 28V
Power monitoring No No
LCD support PanelDue colour touch screen (via expansion connector) PanelDue colour touch screen (dedicated connector)
SD card interface speed 21Mbytes/sec 21Mbytes/sec
RepRapFirmware versions available 1.x series (latest is 1.26.1) 1.x series (latest is 1.26.1)